*As Featured on NI.com
Original Authors: Adam Hartzell, Lightning Hybrids
Edited by Cyth Systems
The Challenge
Creating a system to retrofit new and existing fleet vehicles to reduce emissions and fuel usage.
The Solution
Designing a hydraulic hybrid system that uses NI System on Module (SOM) to hydraulically store otherwise wasted braking energy as hydraulic pressure that can be reused to accelerate the vehicle.
The Story
Medium- and heavy-duty fleet vehicles account for 4 percent of the vehicles in use today; however, they consume 40 percent of fuel used in urban environments. Lightning Hybrids has developed a patented hydraulic hybrid system that can be retrofitted to new or existing fleet vehicles, such as shuttle busses and delivery trucks, to decrease fuel consumption by 20 percent and decrease NOx (the key component of smog) by up to 50 percent. Our system provides a new method for fleet operators to reduce fuel costs, brake wear, engine wear, and pollution. The Lightning Hybrids Energy Recovery System (ERS) uses LabVIEW software paired with a SOM for control. The NI platform has been key to the success of Lightning Hybrids from the beginning. We have used several versions of CompactRIO and Single-Board RIO devices to develop the technology both on and off of vehicles.
Left: These are the major components of the Lightning Hybrid ERS. Right: The ERS is installed between the frame rails of the vehicle, and the hydraulic accumulators are mounted remotely where space is available on the vehicle.
The ERS uses high-pressure hydraulic fluid to store energy that would otherwise be lost as heat during braking. The ERS includes the subsystems outlined below:
Hydraulic Pump/Motor—Converts vehicle kinetic energy into hydraulic energy and then back.
Power Transfer Module (PTM)—Mechanical interface from the hydraulic motor to the vehicle’s drivetrain, which includes a gear reduction and a clutch pack.
Hydraulic Accumulators—These “hydraulic batteries” store energy as high-pressure hydraulic fluid,via nitrogen-filled bladders. o High Pressure—The high-pressure accumulator has a working pressure of up to 6,000 PSI o Low Pressure—The low-pressure accumulator has a working pressure of up to 300 PSI
Hydraulic Manifold—Valve body that acts as an interface between the hydraulic motors and hydraulic accumulators. It is populated with multiple electrically actuated hydraulic valves that proportionally control the amount and direction of fluid flow.
Controller—Used to control every aspect of the ERS. o Actuate hydraulic and pneumatic valves o Interface to the vehicle via CAN to send and receive messages o Record data for use in a telematics system and communicate the data to servers o Provide an interface through an in-vehicle wireless network to a user interface for debug and development o Monitor system performance and ensure safe operation
Left and Center: The V3 ERS controller contains a custom daughterboard and an NI sbRIO-9626.
Right: The V2 ERS controller contains a custom daughterboard that sits on top of the NI CompactRIO modules and a NI cRIO-9075.
During installation, the ERS is installed under the vehicle and incorporated into the driveline between the transmission and the differential. We developed a modular framework so we can quickly retrofit the ERS to most medium and heavy-duty vehicles with minimal new design work or modification to the vehicle. We mount the PTM/manifold combination between the frame rails and the accumulators are placed remotely where space is available. We used high-pressure hydraulic lines to connect the accumulators to the manifold. A custom wire harness is run into the cab and allows for quick integration with the vehicle’s wire harness. The system is designed for easy installation. We can typically commission a new system onto a vehicle in less than a day, which limits downtime for the fleet.
A key component that makes the ERS successful is the high-pressure accumulator. Hydraulic accumulators, typically made from steel, have been around for decades. Traditional accumulators make a poor choice for mobile applications as their high weight impacts the vehicle load capacity and offset much of the economy gains from the hybrid system. Lightning Hybrids uses an accumulator that is composed of an aluminum shell wrapped in carbon fiber and fiberglass. This construction drastically reduces the weight of the accumulator but still allows for high working pressures. Inside the accumulator shell is a nitrogen-filled bladder that functions as a gas spring. As the incompressible hydraulic fluid enters the accumulator, it compresses the nitrogen inside the bladder to store energy.
The ERS control application has three modes of operation:
Hydraulic Idle—The ERS is idle as there is no command for braking/accelerating or the necessary hydraulic charge is not present.
Hydraulic Braking—The driver slows the vehicle. The proper valves are actuated and the ERS applies a torque to the drive shaft to create an acceleration opposite the direction of travel. The work of slowing the vehicle is used to build pressure. The hydraulic motors move fluid from low pressure to high pressure so that it can be used to accelerate the vehicle at a later time. The factory brakes are only needed for emergency stops, traction control, or other non-typical stopping requirements.
Hydraulic Accelerating—The driver is accelerating the vehicle. The proper valves are actuated and high-pressure hydraulic fluid rotates the hydraulic motors to accelerate the vehicle. The available hybrid torque is calculated and used to reduce the throttle signal sent to the engine reducing fuel, emissions, and engine wear. Under some conditions, the ERS can provide up to 100 percent of the torque used to accelerate the vehicle with no engine power needed.
NI software and hardware have been key for us since early in Lightning Hybrids’ history. After some initial experimentation, we quickly focused our efforts on a CompactRIO solution. Our first NI controller was an 8-slot cRIO-9024. We used it for internal prototype development and deployed it in the field in the first pilot systems. We later transitioned to a 4-slot cRIO-9075 as our second-generation controller. We used the CompactRIO controllers to quickly prototype our system. The CompactRIO is flexible enough for the quick changes needed for a prototype, yet still rugged enough to be placed on a vehicle and survive real-world conditions.
*As Featured on NI.com
Original Authors: Adam Hartzell, Lightning Hybrids
Edited by Cyth Systems
Comentários